When performing deck staining, allow the wood to dry for at least 24-48 hours before you stain it with any oil based stain. Once you believe the wood is dry, you should test it with a moisture meter. Be sure to test the areas that do not get much sun, such as close to the house. You are looking for 12% moisture or less. In a pinch, you can stain wood at 15%, but you are really pushing the edge with that.
Take a little time to protect the yard plants and lawn around the deck. Sun Brite Supply has lightweight inexpensive paper-poly drop-cloths that will prevent stain from landing on vegetation. stain blocks the pores of vegetation, so the leaf cannot breathe. Cover up and be safe. NOTE: Never use sheet plastic over vegetation. On a sunny day, plants can fry within minutes.
If there are any fuzzies on the wood, use a sanding sponge with medium grit (or a brass wire brush, an Osborne brush, or a de-felting pad) to go over the entire area. This step will help assure professional looking results.
Remember that Ready Seal is made with inert oil that contains no sugars or starches. We caution you to avoid any stain that contains linseed oil (even in small amounts, linseed oil supports the growth of mildew with its natural sugars and starches). We also caution you about using any stain without superior UV protection. That includes all clear stains. Generally speaking, darker stainant colors contain more UV protection. Ready Seal contains some of the finest pigments available today, combined with exclusive resins that help the stain be absorbed completely into the wood very quickly. Ready Seal is permeable, which means it allows the wood to breathe naturally but will not allow moisture drops to enter the wood.
Using a good brush with white china bristles, apply the stain along the edge of the deck nearest the house. Cover about 12” to 18” out from the house, being very careful to feather the edges so that you avoid a straight, visible line where the brushing stops and the spraying will begin. Cutting-in the edge like this allows you to begin spraying away from the house, minimizing your clean-up at the end of the job. Many contractors spray the entire deck, avoiding the extra labor needed for cutting-in by using sheet plastic or a flexible painter’s shield to protect the house from spray.
A DECKSTER sprayer is the quickest method to apply Ready Seal when used by a professional. On a windy day, the Hurricane Brush will be the fastest way to apply Ready Seal or any other deck sealer on the market without creating a clean-up headache. Ready Seal can also be applied with a pump-up sprayer, but that is more labor-intensive and a less-even application than you get when using a DECKSTER. You may also use a brush or roll it, but those methods are more labor-intensive and usually don’t get the stain on to the sides of the boards like the sprayer does.
Take time to protect any patio under the deck. Stain that drips onto concrete is extremely difficult to remove later on. If you spray the stain, also protect plants and house surfaces. If you must clean up spilled stain or overspray, use mineral spirits or denatured alcohol. Mineral spirits is the best all-around cleaner, while denatured alcohol works very well for cleaning it off glass.
Two light coats (applied wet-on-wet) are much better than one heavy one. Once the first coat of stain has been on the wood for at least 15 – 30 minutes, it will accept a moderate second coat. Once the second coat of stain has been on the wood for about 20 minutes, the wood has absorbed all it will take. If there are any wet or shiny spots visible, they can be wiped with a clean rag or back-brushed with a flat stain pad to remove them.
Ready Seal is really goof-proof. That means that you won’t get lap marks or runs, and it means that rainy weather can’t mess it up. The stained wood is ready to stand up to rain within about 15 minutes after applying Ready Seal. The deck is ready to use immediately, while the stain continues to dry beneath the surface of the wood for about 2-3 weeks.
Expect the color of the newly stained wood to be somewhat darker that the color sample indicated. The wood may also have a slightly splotchy appearance. The color will lighten considerably and even out over the next two weeks or so. The color will continue to lighten gradually, depending on use and exposure to sun. Typically, this process should be repeated every two years or so to maintain optimal appearance and protection.
Peter Marentay, Owner of Sun Brite Inc.
Mr. Marentay joined Sun Brite Inc.in 1998 and immediately created a new division of the company - Sun Brite Supply. Since that time, SBS has become one of the fastest growing suppliers of specialty products to the pressure washing industry.
Pete co-authored the Power Washers of North America Wood Certification course and is currently an Advisory Director of PWNA. He is a PWNA Certified Instructor. PWNA Certification is available separately for those interested at the end of the class.
Pete has taught this 4-day hands-on class since 1999. The important focus of this 4-day course is Profitability.
Toll-free 1-877-5-SUPPLY or 1-877-578-7759
Phone (770) 277-9924
Fax (770) 277-1612
361 Pike Boulevard, Suite 240
Lawrenceville, Georgia 30045