Injection Molding-How Plastic is Molded


Visitors: 736

Plastic has, quite literally, become the cornerstone of our society. We make so many things from plastic that it is hard to imagine what our lives would be like if it was never invented. With so many of our everyday products being made of plastic, it is easy to understand why plastic injection molding is such a huge industry.

Approximately 30% of all plastic products are produced using an injection molding process. Of this 30%, a large amount of these products are produced by using custom injection molding technology. Six steps are involved in the injection molding process, after the prototype has been made and approved.

The first step to the injection molding process is the clamping of the mold. This clamping unit is one of three standard parts of the injection machine. They are the mold, the clamping unit and the injection unit. The clamp is what actually holds the mold while the melted plastic is being injected, the mold is held under pressure while the injected plastic is cooling.

Next is the actual injection of the melted plastic. The plastic usually begins this process as pellets that are put into a large hopper. The pellets are then fed to a cylinder; here they are heated until they become molten plastic that is easily forced into the mold. The plastic stays in the mold, where it is being clamped under pressure until it cools.

The next couple of steps consist of the dwelling phase, which is basically making sure that all of the cavities of the mold are filled with the melted plastic. After the dwelling phase, the cooling process begins and continues until the plastic becomes solid inside the form. Finally, the mold is opened and the newly formed plastic part is ejected from its mold. The part is cleaned of any extra plastic from the mold.

As with any process, there are advantages and disadvantages associated with plastic injection molding. The advantages outweigh the disadvantages for most companies; they include being able to keep up high levels of production, being able to replicate a high tolerance level in the products being produced, and lower costs for labor as the bulk of the work is done by machine. Plastic injection molding also has the added benefit of lower scrap costs because the mold is so precisely made.

However, the disadvantages can be a deal breaker for smaller companies that would like to utilize plastic injection molding as a way to produce parts. These disadvantages are, that they equipment needed is expensive, therefore, increasing operating costs.

Thankfully, for these smaller companies, there are businesses that specialize in custom plastic injection molding. They will make a mock up mold to the exact specifications, run it through the complete process and present the completed piece along with an estimate to complete the job to the customer.

Linda Moore writes on a variety of subjects including home ownership, travel, personal enrichment, plastic injection molding and replacement auto glass


Article Source:

Rate this Article: 
Plastic Or Paper? The Plastic Bag Problem and One Persons Eco Friendly Solution
Rated 4 / 5
based on 5 votes

Related Articles:

The Industrial Science of Injection Molding

by: Rashmi Yadav (February 16, 2011) 
(Business/Industrial Mechanical)

The Lean Manufacturing Process In Custom Injection Molding

by: Randy Hough (May 08, 2008) 
(Business/Industrial Mechanical)

Your Guide To Plastic Molding

by: John Morris (October 26, 2005) 
(Shopping and Product Reviews)

Plastic Extrusion Molding

by: George Ure (July 17, 2008) 
(Business/Industrial Mechanical)

The Advantages and Disadvantages of Green Sand Molding, No-Bake Sand, Resin ..

by: Galen Wang (September 27, 2012) 
(Business/Industrial Mechanical)

Quit Smoking Injection - All You Need To Know About The Injection to Stop ..

by: Mike Singh (December 20, 2006) 
(Health and Fitness)

EPS foam block – How is it manufactured & Molded

by: Tal Barnea (March 10, 2010) 
(Business/Small Business)

Don't Buy Mom a "Molded" Cameo!

by: Jon Kreps (March 19, 2008) 
(Shopping and Product Reviews/Jewelry Diamonds)

Selecting the Best Custom Molded Rubber Parts for Your Water or Hydronics ..

by: Kevin Matt (October 18, 2011) 

Plastic Or Paper? The Plastic Bag Problem and One Persons Eco Friendly Solution

by: Dennis Copson (June 19, 2008)